prod_id=5484 CA: ROGUE ENGINEERING E36/E46 ADJUSTABLE REAR CONTROL ARMS McLAREN STYLE
Tel: 00 44 (0)1202 822 792
Monday - Friday, 10am - 7pm
[email protected]


-WE SHIP WORLDWIDE; 15% DISCOUNT ON LIST PRICES FOR ORDERS OUTSIDE EUROPE UNION.
-WE WILL BEAT ANY OTHER GENUINE QUOTE ! TRY US
Product Details
ROGUE ENGINEERING E36/E46 ADJUSTABLE REAR CONTROL ARMS MCLAREN STYLE
£608.00 inc. VAT
Product Code: rearcamcl



Rogue Eng adj rear control arms McL
Click to Enlarge

Rogue Eng adj rear control arms McL
Click to Enlarge

McLaren cross brace
Click to Enlarge
Description
ROGUE ENGINEERING E36/E46 ADJUSTABLE REAR CONTROL ARMS McLAREN STYLE

Inspiration
As huge fans of the iconic McLaren F1, Rogue Engineering have always been enamoured at it's engineering marvel and beauty. As a tribute to the car, they have produced this special set of adjustable rear control arms (ARCA), inspired by the gold brace in the engine compartment. Anodized in the similar gold hue, their rear control arm is designed to be reminiscent of the engine brace when viewed from behind. The design allows for the intricately machined CNC'd pockets to always face forward and backwards at all times.

What does a ARCA do?
An Adjustable Rear Control Arm (ARCA) determines the rear wheels' camber settings. This is important on vehicles that are lowered or frequent the track. Whereas the factory arms are adjustable, they have limited range because of the eccentric cam bolt design. While lightweight in design, the design of the factory arms cannot withstand the continual pounding of track and street driving forever.

What about the factory arms?
Another undesirable (and overlooked) issue is with the factory control arm's inner mounting bushing itself. If a factory arm were to be replaced (because of damage or otherwise), it is important that the bushings are equally pre-loaded. Because Rogue Engineering's ARCAs arms do not use this style of rubber bushing, there is no chance of unequal bushing pre-load. This means that the suspension is allowed to move equally, freely, quietly, without any binding.

By design, the factory "cam" hardware to allow for camber adjustment has limited range of motion, allowing for only 1.0ยบ. This is to allow the left and right side camber to be equal, more than to allow for additional adjustment for a performance benefit. With the Rogue Engineering ARCA greater range of adjustment, that extra bit of handling is available.

When a BMW is lowered, it can cause additional and unwanted negative camber (which leads to premature and uneven tyre wear) which the factory rear control arms do not have the ability to dial out. Additionally, factory rear control arms are frequently damaged when an E36/E46 is towed by unknowing tow truck operators, who easily find the factory arms a convenient (but incorrect) location to secure the vehicle.

Rogue Engineering Design Details
Rogue Engineering have modified their ARCAs over the years to continually improve the performance and function. Our latest changes allow for a simpler, stronger part at the same time, allowing for easier adjustments when required. However, when considering the design details of their arm, Rogue Engineering specifically identified a few issues with other available arms:
- Adjustment points must be easily accessible. When companies design their arm with simplicity at stake, they tend to put the adjustment points on the ends of the arm. While the one near the clevis is easily accessible, an adjustment point near the subframe is not. Typically, the adjustment nut is so far into the subframe you cannot clearly access it to tighten or loosen it adequately.
- Having replaceable parts is a must. Not all parts will last forever, and when they require replacement, easily sourced parts is key. This is the reason Rogue Engineering use a rod end that is 5/8"-18 (LH) on their ARCA. In case it requires replacement, one can be sourced quickly around the country (outside the US may take longer).
- Mild steel parts do not hold up well in areas where roads are salted during the winters. This wrecks havoc on steel parts. Using parts such as aluminum and stainless steel help against these corrosive elements. When appropriate, Rogue Engineering balance the use of anodized aluminum and stainless steel in the design and construction of our parts. It's more costly, but we want our parts to last.

Kit includes two (2) complete arm assemblies.
Professional installation is recommended as an alignment is necessary to dial in the exact amount of negative camber.

Features and Benefits
- Lighter than stock, factory rear control arm, with more adjustment range. (Factory arm is 1242g each, RE arm is 1065g each)
- Two piece design allows for easier adjustments (no adjustments required near the subframe, only near the wheel!)
- CNC'd 6061-T6 aluminum "arm" and "fork" clevis end is corrosion resistant, lightweight, yet incredibly strong
- One piece, CNC'd hardened 4140 chromoly turnbuckle
- Precision, rod end with grease fitting allows for easy maintenance.
- Made in the USA
- Sold as a PAIR

Fits the following vehicles:
- All E36 including M3 (not Z3 or 318ti)
- All E46 including M3 and xi
- All E85 MZ4 Coupe/Roadster


Estimated Volumetric Shipping Weight : 4.00 Kg
 




© 2019    Site Maintenance by C2G Ltd